WS 160 Flat KBZET, space air system WS 160 Flat KBZET additionally with zone flap

Space air system WS 160 Flat KBZET additionally with zone flap

Comfort-Bypass-Zones execution: Central unit with enthalpian heat exchanger, integrated bypass, preheating register and motor zone flap. The room air is therefore optimally cooled at high outside temperatures and is comfortably pre-heated at deep outside temperatures. In addition, the zoning flap allows a division of the inlet dreams into two zones. The use of the motor zone flap and demand-oriented zone control allow the supply-to-air dreams to be divided into 2 zones. The respective distribution of the volume flows between the 2 zones can be stored in the time programme or controlled by appropriate air quality sensors in the zones. Short description: Intelligent ventilation device with heat and moisture recovery for controlled ventilation and ventilation with a flow volume of 40 to 160 m3 / h Two supply-to-supply (left and right) and one exhaust-to-air (middle) allow a cross-free installation of the supply-to-supply lines. Complete separation of the exhaust air / supply system throughout the device. This prevents unwanted air circulation. Viruses (e.g. Corona virus) and bacteria are not transmitted. Hygiene certificate according to VDI 6022, sheet 1 available. Compact and highly efficient - Energy efficiency class A. Sound and energy-optimized fans in EC technology. KfW eligibility and NRW support are available. Especially suitable for the modern new building or renovation. Mounting options: ceiling-hanging, wall-mounted or in the roof-sloping. No pressure variability: The integrated / automatic volume flow control ensures a permanent compliance of the set volume flow under all operating conditions (e.g. filter pollution, air venting settings). This also results in a simpler start-up / air measurement on the valves. No adjustment of the volume flows is necessary. Very quiet device with very low height (23 cm): especially suitable for installation in suspended ceilings. In addition, it is also suitable for installation in the roof. Various operating modes: off, manual, car sensor, CO2 exhaust air, CO2 supply air. Room air control RLS 1 WR in delivery. ISO Coarse 80% (G4) filters in the exhaust air and ISO ePM1 55% (F7) pollen filters in the outside air. A filter cascade (ISO Coarse 80% / ISO ePM1 55%) in the outdoor air is possible to increase the filter time. The ventilation device is equipped with a state-of-the-art enthalpian heat exchanger with a health certificate according to VDI 6022, sheet 1. The WS 160 Flat can be controlled via APP (air @ home) and the browser-based web tool (www.air-home.de) via an integrated LAN interface. Plug & Play: Easy commissioning through free commissioning software and standard USB connection for commissioning, control update and service. A standard integrated combis sensor (humidity / temperature) in the exhaust air allows a demand-led ventilation operation as well as an intelligent dehumidification strategy (overmoisture protection). The device is also characterised by a freeze protection strategy adapted to the real needs. The heat recovery device has a multi-function contact for the control of e.g. sole- earth heat exchanger (unregulated pump), operating and fault display, preheating or post-heating register, external valves or cooling. 2 input contacts (12 V and 230 V) are available for e.g. safety-related shutdown. Various inputs / outputs allow for a control connection to other home-technology devices, e.g. heat pump. Integrated MODbus interface (TCP / IP and RTU) for integration into the building management technology. The optional K-SM plug module allows integration into KNX building systems. The E-SM optional plug module allows integration into EnOcean systems. Optional additional panels ZP 1 and ZP 2 for extension functions such as pressure control of the EC fans, zone flap, solar heat exchanger (controlled pump), filter differential pressure measurement. Maximum device flexibility through various equipment / connection options. Modern device module technology allows a high user-friendliness for service and maintenance. Housing: powder-coated steel sheet housing. Filter change possible without tools. Tight, heat-free, and sound-insulated internal housing made of temperature-resistant, sound-proof and heat-insulating EPC material. EPP housing with very good hygienic / non-hygroscopic properties. The device surface and interior housing are easy to clean. Filter: ISO Coarse 80% (G4) filter in the exhaust air and ISO ePM1 55% (F7) pollen filter in the outside air. Tool-less filter change. Operation: Ready to use with on / off switch. Control part RLS 1 WR in delivery, 4 air levels, filter change indicator, fault indicator. Further control parts can be connected in parallel. Mobile operation using APP (air @ home) or browser-based web tool (www.air-home.de) via smartphone, laptop or PC allows for example live message, user management, demand-driven automatic / time-controlled automatic operation, manual operation / OFF, ECO- operation supply air, filter queries, error messages, optional touch-screen control software, RLS T2 WS for the setting of 2 automatic mode of operation (car / time), ECO- power-to-power-power-to-power-power-to-power-power-to-power-power-to-power-power-to-power-power-to-power-power-to-power-power-to-power-power-to-power-to-power-power-to-power-to-power-to-power-to-power-to-power-to-power-to-power-to-power-to-power-to-power-to-power-to-to-power-to-power-to-power-to-to-power-to-power-to-power-power-to-power-to-to-to-power-to-power-to-power-power Network connection via integrated LAN interface. Smart-Home ready (e.g. Loxone via Modbus TCP / IP). Modbus TCP / IP and RTU integrated as standard. Optional KNX plug module K-SM for integration in the building management technology www.knx.org. Optional EnOcean plug module E-SM for device integration into the EnOcean world www.enocean-alliace.org. Control: Serial required flow control (relevant moisture value). Continuous adjustment of air volumes. Integrated overmoisture protection function. 3 temperature sensors in the external, forward and supply air. 1 combis sensor (temperature and humidity) in the exhaust air. Up to 4 external sensors of different types (CO2, VOC, humidity) can be connected. Multi-function contact for the control of e.g. sole- earth heat exchanger (unregulated pump), operating and fault display, preheating or post-heating register, external flap or cooling. Inputs for safety-related shutdown over 12 V contact or 230 V contact (e.g. smoke detectors, fire alarm, differential pressure-free fire site). Additional key input for triggering time-limited intensive ventilation (shock ventilation). Extensible via optional additional board ZP 1 for the control of: 3-way flap (e.g. air-earth-heat exchanger), a controlled pump (e.g. solar-earth-heat exchanger), switching contact use for external post-heating register, extensible via optional additional board ZP 2 for: pressure stability of the EC fans, differential pressure-controlled filter monitoring, various inputs and outputs allow a regulatory connection of the ventilation device with another building device such as heat pump. Authorisations and certificates: DiBt approval. PHI certificate. Test report according to DIN EN 13141-7. Certificate according to Swiss energy cluster.ch. Hygiene certificates for housing material (EPP) and heat exchangers. Heat exchanger / heat recovery: High-efficiency enthalpian cross-current heat exchanger. Heat recovery up to 84% and moisture recovery up to 53%. Hygiene certificate (no bacteria, virus growth / virus transition) according to VDI 6022, sheet 1. Heat exchangers with water can be cleaned, antimicrobial. No capacitor connection necessary. Bypass: The integrated bypass flap (100% bypass) with the required bypass control allows a continuous bypass control. Depending on temperature differences and user settings, the room air is optimally cooled without any signs of train. Frost protection: The power-controlled pre-heating register is controlled according to different sizes in the device. The result is an efficient and energy-saving regulatory strategy. The ventilation with the heating register therefore has no comfort loss even at lower outdoor temperatures. Ventilators: forward curved radial fans in the open air or outside air. Energy-efficient EC DC motors with integrated volume current control. Possibility of the pressure control via the optional additional board ZP 2. 4 ventilation levels from 40 m3 to 160 m3 / h can be adjusted continuously. Mounting instructions: Light, very time-saving installation by direct screwing of the device on the ceiling / wall. The case cover can be easily disassembled by screw.Article: WS 160 Flat KBZET, version: Comfort-Bypass-Zone-version, number of ventilation levels: 4, conveyor volume: 40 m3 / h - 160 m3 / h, volume constant: yes, SEC average: -34.1 kWh / (m2 * a), energy efficiency class: A, voltage: AC-current: 230 V, power supply frequency: 50 Hz / 60 Hz, inside diameter: 1 / 2 mm (1), size: 1 / 2 mm (1 / 2 mm), size: 1 / 2 mm (2 mm). Heat supply according to DIN EN 13141-7 (A7): 76%, heat exchanger type: Enthalpie- cross-current, heat recovery with enthalpie- heat exchanger according to DIN EN 13141-7 (A2): 53%, power preheating register: 0,7 kW, position exhaust: left / right, bypass: yes, pre-heating register: integrated, zone valve: yes, enthalpie- heat exchanger: yes, frost control: yes, summer control: ECO2S, optional control of the air quality control (RLS): 4S), control of the control of the control of the air: 4H (RLS), optional control of the control of the control of the air, (RLS: 4H): 4W, control of the control of the control of the control of the control of the control of the control of the control of the control of the control of the air, (RLS, Speed: 3300 1 / min